RAW FILE CONVERTER EX powered by SILKYPIX (Ver.3.2.23.0) Installer for Macintosh OS X 10.6.8 - 10.10

Overview

This software is to install or update RAW FILE CONVERTER.

System Requirements

OS Mac OS X (Ver.10.6.8-10.10)*
CPU Intel (Core 2 Duo or better)
RAM 1GB or more
Free disk space A minimum of 200 MB required of installation with 400 MB available when RAW FILE CONVERTER is running
Video 1,024 x 768 pixels or more with 24-bit color or better
  • * Other versions of Macintosh are not supported. Only pre-installed operating systems are supported; operation is not guaranteed on home-maide computers or computers that have been upgraded from earlier versions of Macintosh.

Detail of the update

The firmware update Ver.3.2.23.0 incorporates the following issues:

  • Applicable models for the RAW FILE CONVERTER are added.
    • FUJIFILM X100T

The firmware update Ver.3.2.22.0 incorporates the following issues:

  • Applicable models for the RAW FILE CONVERTER are added.
    • FUJIFILM X30

The firmware update Ver.3.2.21.0 incorporates the following issues:

  • Applicable models for the RAW FILE CONVERTER are added.
    • FUJIFILM X-T1

The firmware update Ver.3.2.20.0 incorporates the following issues:

  • Applicable models for the RAW FILE CONVERTER are added.
    • FinePix S1

The firmware update Ver.3.2.19.0 incorporates the following issues:

  • Applicable models for the RAW FILE CONVERTER are added.
    • FUJIFILM X-E2 / XQ1

The firmware update Ver.3.2.18.0 incorporates the following issues:

  • Applicable models for the RAW FILE CONVERTER are added.
    • FUJIFILM X-A1

The firmware update Ver.3.2.17.0 Incorporates the following issues:

  • Image quality is improved for models in which "X-Trans CMOS sensor" or "X-Trans CMOS II sensor" is incorporated.
  • Applicable models for the raw file converter are added as follows
    • FUJIFILM X-M1 / X100S / X20
    • FinePix F900EXR / HS50EXR / SL1000

The firmware update Ver.3.2.12.1 incorporates the following issues:

  • Applicable models for the raw file converter are added as follows
    • FUJIFILM X-E1 / XF1 / X-Pro1 / X-S1 / X10
    • FinePix X100 / F800EXR / F770EXR / F775EXR / F600EXR / F605EXR / F550EXR / F505EXR / HS30EXR / HS33EXR / HS20EXR / HS22EXR
  • It is compatible to OS X 10.8.

The firmware update Ver.3.2.9.1 incorporates the following issues:

  • Applicable models for the raw file converter are added as follows
    • FUJIFILM / X-Pro1 / X-S1 / X10
    • FinePix X100 / F770EXR / F775EXR / F600EXR / F605EXR / F550EXR / F505EXR / HS30EXR / HS33EXR / HS20EXR / HS22EXR
  • Improvement of the color cast at the bright area in the RAW data of X-Pro1 when shooting with the high brightness condition.

Regarding install software

  • * If you have a inquiry, please contact your local FUJIFILM support center or through "Contact US" below.
  • * This software is made by "Ichikawa Soft Laboratory". When you install it, you need to accept "Ichikawa Soft Laboratory License Agreement".

Note

  • * The speaification of the software can be changed without notice.
  • * FUJI EXPRESSLY DISCLAIMS ANY WARRANTY FOR SOFTWARE. SOFTWARE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF COPYRIGHT, PATENT, TRADE SECRET, OR ANY OTHER PROPRIETARY RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL FUJI BE LIABLE FOR ANY GENERAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR OTHER DAMAGES RESULTING FROM THE USE OF OR INABILITY TO USE SOFTWARE.